This product is not visible to your customers.
[Gudmaker] GUDMAKER MAGLATE PEI BUILD PLATE - 310x310MM
Auckland Local Stock
Features:
Textured/Smooth Double-Sided PEI Magnetic Plate for 3D Printing and Magnetic Sticker with Adhesive
Size:310x310mm
Fits Ender-3 MAX / Creality CR-10 / CR-10 Smart / CR-10 Smart Pro / Creality CR-10S /
Lulzbot Taz 6 / Lulzbot Taz 5 / Tevo Tornado / Hictop Prusa i3 DIY / Anet E12 / E16 / A8 PLUS / ET5 / ARTILLERY SW-X1)
Compatible with PLA、PETG、PEEK、ABS and any other filaments.
The magnetic base can resist up to 130℃/266℉, so you can heat your bed to high temps for specialty filaments and not worry about loss of performance.
Package included:
1 pcs × PEI Double-side coated Build plate
1 pcs × Magnetic Sticker
We also offer size of 235*235mm Pei Build Plate
STOP DAMAGING PRINTS:
Never scratch, gouge, or damage your print or build plate ever again! Just remove the spring steel plate when finished printing, flex the part off, and snap the Maglate one back onto the included magnet!
TWO SIDES, TWO FINISHES:
Our double-sided PEI flex plate features one powder-coated PEI surface that leaves a textured matte finish on your parts and one smooth PEI finish that leaves a glossy, reflective finish on the bottom of your parts!
PRINT RELIABLY:
Increase printing success rate with our PEI coatings. PEI grips parts with strength when heated then releases them when cooled. Print across the entire build plate with confidence. Part adhesion for our Maglate series is guaranteed!
WHY Gudmaker Maglate series:
We do lots of test to make sure the perfect status no matter for PEI Process timing or thickness and stiffness of spring steel. The maximum temperature for printing is 130℃ on the bed., It's perfect for materials like PLA, PETG, ABS, TPU, ASA, Nylon, and Polycarbonate!
Highlights:
Maglate 2s double-sided PEI flex plate features one powder-coated PEI surface that leaves a textured matte finish on your parts and one smooth PEI finish that leaves a glossy, reflective finish on the bottom of your parts!
Maglate textured PEI and the smooth PEI sheet are very easy to use, simply stick the magnetic bottom sheet onto your heated bed, then place the steel platform with PEI surface on the top. The maximum temperature for printing is 130℃ on the bed.
Excellent adhesion can be achieved when the temperature of the heated bed is about 60℃, you can print directly on the Maglate PEI sheet without using any glue or other tools to help the model to stick onto the sheet. You do not need to worry about the prints curling with a 60℃ bed temperature.It also can print PETG very well, but the temperature of the hotbed needs to be about 80-85℃
Prints come off the surface easily when the temperature of the heated bed reaches room temperature. If the print is still stuck, gentle flexing of the plate will help remove it.
The size of 310x310mm(12.2*12.2inch), it is applicable with CR-10, CR-10S,Tenlog D3 pro,Longer LK1, Artillery SW-X1, SW-X2 and other same sized 3D printers.
Gudmaker's PROMISE:
For Maker, We Made. Always delivery the best to Maker, We offer knowledgeable tech support if join Gudmaker membership. Reach out to us with any issues and we'll make it right!
Cleaning & Maintenance :
Do not wash or clean the PEI with any water, strong chemical reagents or strong detergents. Please Clean the dust with a soft cloth. Wipe the stains with low concentration alcohol gently.
Package Details:
Maglate 2s - 310
|
|||
Gift Box (mm) |
330*345*10mm
|
Net Weight(g) |
810g
|
QTY / Carton(Pcs) |
1pcs
|
Gross Weight(g) |
980g
|